Chimney Advice · Warrington

Cracks and Open Joints in a GRP Chimney: What Can Be Repaired

A moulded stack has no mortar to repoint, so repair means something different. Here is what can honestly be mended, what is only a patch, and when a new moulding is the better answer.

★ 5.0 from 74 Google reviews
✓ Repointing, flaunching, leadwork & pots
✓ Fully insured
✓ Free written quotations
✓ Chester, Cheshire & Wirral
Home › Chimney Repairs › Chimney Repairs Warrington › Cracks and Open Joints in a GRP Chimney: What Can Be Repaired
The short version
  • Fine crazing in the surface colour is mostly cosmetic; a single line crack or an open seam is not.
  • Mastic alone is a short-lived patch, so a lasting repair deals with the cause and the fixings.
  • New fixings need sound timber to bite into, and loose fixings are behind many cracks.
  • A moulding that is brittle, bowed or split in several places is usually better replaced.
  • The flue inside belongs to a HETAS or Gas Safe registered installer, not a roofer.

Sorting the cracks that matter from the ones that don’t

A glass-reinforced moulding shows its age on the surface first. Sunlight and heat cycling break down the gel coat, the thin pigmented skin on the outside, and it develops a web of hairline crazing that looks like cracked paint. On its own that is mostly cosmetic, because the glass fibre layer behind it is still intact and still keeping water out. It is worth photographing from the ground and watching, rather than treating as an emergency.

Cracks that matter look different. They run in a single line rather than a web, they usually start at a corner, a screw head or the edge of a moulded detail, and they are often wider at one end. If the line looks dark rather than pale, or the two edges sit at slightly different levels, the split has probably gone right through the wall of the moulding. Water will find that route in a heavy shower and run down the inside, where nobody can see it.

The third category is the seam. Many dummy stacks are made in halves or in four sides that are bonded together and finished over. When that bond opens you see a straight, usually vertical line on the weather-facing side that was not there before. Gales and strong sun on one face are the usual causes. Seams are where a repair can become fairly involved, which brings us to what is actually done.

What a sound repair to the moulding involves

Mending glass fibre is a laminating job rather than a building job. The damaged area is cleaned and ground back to a chamfer, new layers of glass mat or cloth are built up in resin from behind where that can be reached or from the face where it cannot, and the surface is then filled, sanded and recoloured. For a localised split or a small hole that is a reasonable repair. It depends on dry weather and a clean, dry surface, and a colour match to a weathered face is never perfect.

The limit is extent. A single crack at a corner, or a hole left where something was once fixed to the face, is a fair candidate. A long seam or damage in several places is a different matter, because each repair stiffens one part of a thin, flexible shell and moves the stress to the next weakest spot. We will say plainly when we think a repair is only buying time, and we will not dress up a cosmetic patch as a structural one. We make no claims for any particular resin or product, and you should be wary of anyone who does.

Anything touching the flue is a separate matter. If a crack or a repair might expose the twin-wall pipe, its insulation or the seals at the terminal, those parts are for a HETAS or Gas Safe registered installer to look at. Our work stays on the outside of the moulding and the roof around it.

Sealant, and why it is not the whole answer

A bead of sealant is the first thing most people try, and for a hairline gap it is a sensible stopgap. The trouble is the job it is asked to do. A flexible bead bridging a joint that moves with every gust and every sunny afternoon will last a season or two, then harden, shrink and peel from one edge. It also hides the gap, so the joint looks closed while water enters behind the bead.

Where sealant is used it works best as the last layer rather than the first. The joint is opened slightly and cleaned, loose or chalky material is taken out, the faces are dried and the gap is filled to a depth that lets the sealant stretch instead of sitting in a shallow groove. Colour matters as well, since black mastic on a brick-pattern face looks like exactly what it is. The sealant must also be compatible with glass-reinforced plastic, because some types will not stick to it and some attack the surface.

At the foot of the moulding, where it meets the tiles, sealant is the wrong material to rely on at all. That junction is a roofing detail and is better made in lead dressed into the covering. The reasoning is the same as in our guide to Lead Flashing or a Cement Fillet? How to Tell Which You Have, where the hard, brittle option loses to the flexible one.

Fixings: the repair people forget

A moulded stack stays up because it is strapped or screwed to a timber kerb built off the rafters. If those fixings have worked loose, no amount of filling will hold. The shell flexes with each gust, the cracks reopen and the next repair fails like the last. Many cracks beside screw heads are not faults in the plastic at all, but the result of a fixing that has pulled, or been overtightened.

Renewing fixings means checking what they bite into. Screws turning in a soft or undersized batten hold nothing, so the first question is whether the kerb is sound. Where it is, new stainless fixings go in with washers that spread the load across the thin wall, and the holes are sealed afterwards. Where it is not, the kerb is repaired first, and that is a carpentry and weathering job under the moulding rather than a repair to the moulding.

This is also why aerial brackets and dish arms do so much harm. Bolted through a thin shell, they concentrate load on a few small holes, and splits fan out from them. If you want to know whether the unit on your roof is a moulding or masonry in the first place, What to Look For on a Chimney From the Ground covers what can be judged without leaving the garden.

When replacing the moulding is the wiser choice

Some stacks are past repair in any useful sense. A shell that has gone chalky and brittle all over, that cracks further whenever it is touched, or that is split at several corners and seams has reached the end of its useful life. The same applies if it has bowed and no longer sits squarely on its kerb, because it can no longer be weathered properly at the base. Patching in that condition is paying repeatedly for something that will not hold.

Replacement is more straightforward than it sounds, because there is no masonry to take down. The old moulding comes off, the kerb and the weathering are checked and put right, and a new one is fixed and flashed. Compare that honestly with repeated repairs, much as Repoint, Rebuild or Remove? How the Decision Gets Made does for brick stacks.

Ask for the choice in writing. A quotation should say whether the work is repair or replacement, what happens to the fixings and the lead at the base, and what is excluded. We give free written quotations and are fully insured, and you can start with a description or a phone photograph from the garden for chimney repairs in Warrington. Please do not climb up to look; a zoomed photograph from below shows a good deal.

Not sure what you are looking at? Describe it and we will tell you what it is likely to be — 07464 259566, WhatsApp, or Evensbuddy@yahoo.com. If water is coming in now, please call rather than email.
FAQs

Common Questions

How can I tell whether a crack goes right through the moulding?
Look at the edges from the ground with binoculars or a zoomed phone photograph. A pale web of fine lines is surface crazing. A single dark line, with edges sitting at slightly different levels or a gap you can see light through, has probably gone through the wall. Never climb up to check; send us the photograph instead.
Will a repaired crack show afterwards?
Usually a little. The pattern is pressed in at the factory, so a repaired patch has to be rebuilt by hand and recoloured to match a face that has weathered. From the road a careful repair is hard to spot, but close up the join is rarely invisible, and a very faded face makes a match harder.
Is sealant ever enough on its own?
For a hairline gap that is not moving it can be a sensible short-term measure, but it hides the problem and tends to perish. If the gap sits at a seam, a corner or a fixing, the cause usually needs dealing with as well, otherwise the bead simply fails again in a season or two.
Who looks at the pipe inside if the shell is damaged?
The flue itself, including its joints, insulation, seals and the terminal, is for a HETAS or Gas Safe registered installer. We work on the outside of the moulding and the weathering around it, and we will tell you if something we find looks like a flue matter rather than a roofing one.
More Advice

Other Chimney Guides

More from the Warrington chimney series, then the wider guides.

Where We Work

Chimney Repairs Across Cheshire & the Wirral

Every town has its own page, written around the stacks that are actually on the roofs there. Start with the main chimney repairs page.

Customer Reviews

What Our Customers Say

5.0
★★★★★
74 Google reviews
★★★★★

“Excellent work replacing ridge tiles, repointing chimney and repairing flashing. Also fixed other broken tiles. Clean and tidy job. Would definitely recommend.”

Neil
★★★★★

“The guys did a great job in repairing our chimney. They were reliable, friendly and efficient. Buddy kept me in the loop throughout the whole process and I would not hesitate to use Roofline again!”

Hollie Furnival
★★★★★

“Highly recommend. Very quick and efficient. Great communication. Went above and beyond to work the weekend to complete the work that needed to be done. Very happy with the results.”

Karen Jones

Leave Roofline Solutions a Google review →

Free Quotation

Tell Us About the Chimney

Describe what you can see and roughly where you are, and we will come back to you — usually the same day. If water is coming in now, please call instead.

Prefer to talk? Call 07464 259566 · WhatsApp 0044 7464 259566 · Email Evensbuddy@yahoo.com

Find Us

Roofline Solutions, Elton, Chester

We cover Chester, Cheshire, the Wirral and Flintshire from Elton, just north of Chester.

Where We Are

2 Manley View
Elton
Chester
CH2 4QF

Almost all of our work happens at your property rather than here, so please call before travelling.

Opening Hours

Monday – Friday — 24hrs — Emergency Call-Outs
Saturday — 8:00 – 19:00
Sunday — 8:00 – 19:00

Weekday emergency call-outs are answered around the clock. Weekend cover is 8:00 to 19:00.