Chimney Advice · Bebington

How a Chimney Back Gutter Should Fall and Drain

A back gutter is simple in idea and fussy in practice. This guide covers the shape it needs, why short lengths of lead matter, and what makes a flat or dished gutter hold water.

★ 5.0 from 74 Google reviews
✓ Repointing, flaunching, leadwork & pots
✓ Fully insured
✓ Free written quotations
✓ Chester, Cheshire & Wirral
Home › Chimney Repairs › Chimney Repairs Bebington › How a Chimney Back Gutter Should Fall and Drain
The short version
  • Water must always have somewhere downhill to go, so the gutter needs a fall to each side.
  • Width matters: a gutter too narrow to work in is usually too narrow to drain.
  • Lead is laid in short lengths joined by rolls or drips, not one long sheet.
  • A flat or dished gutter holds water, and standing water finds the laps.
  • A water test on a dry day shows more than any amount of guessing.

What the gutter has to do

A back gutter has one job, which is to take the water that runs down the roof slope behind a chimney, hold it for a moment, and pass it sideways to either end so it can drain onto the roof beside the stack. Everything about its shape follows from that. If water can reach the low point and leave, the gutter works. If it can sit anywhere, it eventually finds its way through whatever joint is nearest.

The trough is formed over a timber base. Its floor has to slope from the middle of the stack toward each side, so the highest point is under the centre of the chimney and the lowest points are at the outlets. On a narrow stack the fall is short and gentle. On a wide stack it needs to be steeper or the water will move too slowly to clear a heavy downpour. The slope is built into the timber before any lead goes down, which is why it cannot be put right afterwards by pressing the lead into shape.

It also has to be wide enough to be built properly. A gutter that is only a hand wide behind the brickwork is hard to line and harder to keep clear, and it fills fast. Where there is room, a wider trough carries more water and is more forgiving of leaves and silt. Where there is no room, the options are to adjust the tiling behind or to accept a smaller design, and that choice should be made on site, not guessed.

Falls, outlets and the line the water takes

Each outlet needs somewhere to discharge. The lead at the end of the gutter is carried out over the tiles or the side flashing and dressed to throw water clear, so it lands on the covering below instead of running back into the corner. On a stack set close to a hip or valley the run of roof available is short, and the outlet has to be formed so the water leaves in a controlled direction, not into a junction where it collects.

A good test of the layout is to follow a single drop of rain. It lands on the slope above, runs down onto the tilting fillet, drops into the trough, runs along the fall to an end, and leaves over the lead onto the tiles. At no stage should it be able to stop. Any point where it could stop, such as a hollow in the timber, a lump of mortar or a lead fold that traps a little water, is a point where it will, and standing water behaves differently from running water because it has time to find the tiny capillary gaps in a lap.

This is also why the gutter cannot be treated as a separate item from the stack. The shape of the brickwork decides where the upstand goes, the width of the slope above decides how much water arrives, and the coverings either side decide where the outlet can discharge. Our chimney repairs in Bebington page describes how that works on hipped roofs; this guide is about the shape that results once the layout is settled.

Short lengths, rolls and drips

Lead expands and contracts with the temperature, and a long sheet fixed at both ends has nowhere to go. It stretches in the warmth, cannot return in the cold and eventually cracks, most often at a fixing or a fold. For that reason the gutter is made in a series of shorter pieces, each one lapped over the next, so movement is shared out instead of building up in one place.

The joints between lengths are made as rolls or drips. A roll is a raised section of lead formed over a timber core, which lets water pass beneath the join without touching it. A drip is a small step in the floor of the gutter, so the upper length overlaps the lower and water drops over the edge, rather than seeping sideways. Both are ways of making sure the lap is on the downhill side and that water is always running away from the joint, not toward it. A drip is the usual choice on a gutter with any real run, as it helps the fall as well.

What does not belong in a back gutter is a long, unbroken strip of lead with its overlaps stuck down with mastic, or one that has been folded to fit and so has creases in the floor. Creases weaken the lead and hold water. If the lead is of the right thickness, supported by the timber beneath and fixed along its top edge only, it has room to move and can last a long time. How it joins the stepped flashings on each side is covered in our guide on Lead Flashing or a Cement Fillet? How to Tell Which You Have.

Why flat and dished gutters hold water

A flat gutter is simply one built without a proper fall. It may look neat, and in dry weather it will seem fine, but after rain a thin layer of water stays on the floor, and the laps are underwater for hours. A dished gutter is one that started with a fall and has lost it. The timber beneath has sagged, or the lead has been walked on, or the sole board has been pressed down by years of wet debris, and a hollow has formed in the middle.

Both have the same effect. Water that has nowhere to go sits against the upstand and the laps, and lead is not the problem here; the joints are. Water rises by capillary action through narrow overlaps, finds the brickwork behind and travels down inside the wall. The stain on the chimney breast or the bedroom ceiling that results can be misread as a problem with the mortar, which is how so many stacks end up repointed without curing the leak.

A simple check is possible without a ladder. After a dry spell, a gutter that has been made well will be visibly dry within an hour or two of the rain stopping. If you can see the junction from an upstairs window and it is still shining long after the rest of the roof has dried, water is sitting there. Take a photograph, and talk to us about it. Our free written quotation will say whether the gutter needs only clearing, relining or a full rebuild; what to expect from one is on What Should Be on a Chimney Repair Quotation?.

Not sure what you are looking at? Describe it and we will tell you what it is likely to be — 07464 259566, WhatsApp, or Evensbuddy@yahoo.com. If water is coming in now, please call rather than email.
FAQs

Common Questions

How wide does a back gutter need to be?
There is no single figure, because it depends on the width of the stack, the slope behind and the room the builder left. The aim is a trough wide enough to line properly, to carry a heavy downpour and to be cleared by hand. Where space is tight, the tiling behind can sometimes be altered to give it more room.
Is a back gutter better with a roll or a drip?
Both work if they are made correctly. A roll lifts the joint above the water. A drip drops the water over a step so the lap is never in its path. A gutter with real length usually benefits from drips because they also help the fall. The choice is made on site, depending on the width and the lead thickness.
Can a flat back gutter be corrected without rebuilding it?
Seldom. The fall is built into the timber beneath the lead, so correcting it means lifting the lead and reforming the base. Sometimes the existing lead can be reused, but it is often worn at the folds by then. Trying to push a fall into old lead tends to crease it and shorten its life.
Why does a gutter that looks fine from the ground still leak?
You cannot see a back gutter from the ground at all, only its effects. A tiny dip, a split at a lap or a poorly chased upstand can let water through while the visible lead looks sound. Staining indoors in heavy rain, and moss in a line behind the stack, are better guides than any view from below.
More Advice

Other Chimney Guides

More from the Bebington chimney series, then the wider guides.

Where We Work

Chimney Repairs Across Cheshire & the Wirral

Every town has its own page, written around the stacks that are actually on the roofs there. Start with the main chimney repairs page.

Customer Reviews

What Our Customers Say

5.0
★★★★★
74 Google reviews
★★★★★

“Excellent work replacing ridge tiles, repointing chimney and repairing flashing. Also fixed other broken tiles. Clean and tidy job. Would definitely recommend.”

Neil
★★★★★

“The guys did a great job in repairing our chimney. They were reliable, friendly and efficient. Buddy kept me in the loop throughout the whole process and I would not hesitate to use Roofline again!”

Hollie Furnival
★★★★★

“Highly recommend. Very quick and efficient. Great communication. Went above and beyond to work the weekend to complete the work that needed to be done. Very happy with the results.”

Karen Jones

Leave Roofline Solutions a Google review →

Free Quotation

Tell Us About the Chimney

Describe what you can see and roughly where you are, and we will come back to you — usually the same day. If water is coming in now, please call instead.

Prefer to talk? Call 07464 259566 · WhatsApp 0044 7464 259566 · Email Evensbuddy@yahoo.com

Find Us

Roofline Solutions, Elton, Chester

We cover Chester, Cheshire, the Wirral and Flintshire from Elton, just north of Chester.

Where We Are

2 Manley View
Elton
Chester
CH2 4QF

Almost all of our work happens at your property rather than here, so please call before travelling.

Opening Hours

Monday – Friday — 24hrs — Emergency Call-Outs
Saturday — 8:00 – 19:00
Sunday — 8:00 – 19:00

Weekday emergency call-outs are answered around the clock. Weekend cover is 8:00 to 19:00.