Chimney Advice · West Kirby

Re-Roofing Around an Existing Chimney: Why Flashings Are Renewed

A new roof covering is only as watertight as its joins to the chimney. Here is why the stack junction is redone during re-roofing and how to coordinate it.

★ 5.0 from 74 Google reviews
✓ Repointing, flaunching, leadwork & pots
✓ Fully insured
✓ Free written quotations
✓ Chester, Cheshire & Wirral
Home › Chimney Repairs › Chimney Repairs West Kirby › Re-Roofing Around an Existing Chimney: Why Flashings Are Renewed
The short version
  • New tiles change the levels the old flashings were made for.
  • Old lead and mortar fillets rarely survive being lifted and relaid.
  • The stack junction is cheapest to renew while the covering is off.
  • Agree in writing who forms the flashings, and when.
  • Flue work stays with a HETAS or Gas Safe registered installer or a sweep.

Why the old flashings do not simply go back

When a roof is stripped and recovered, the new covering is laid at slightly different levels from the old. Tiles vary in thickness, new battens may be a different depth and underlay changes the profile of the whole slope. A flashing formed to suit the old surface will not sit against the new one, and a gap of a few millimetres is enough for wind-driven rain to get through.

Then there is the material itself. Lead that has weathered for decades has been through countless cycles of expansion, and it work-hardens. Bending it back to a new position often cracks it along old creases. Mortar fillets are worse: once the tiles are lifted, the fillet is disturbed or broken, and it never reseats cleanly. Neither is worth trying to reuse.

The sensible approach is to treat the stack junction as part of the re-roof. Strip back the old flashings, assess the stack faces beneath, form new lead to suit the new levels and then lay the covering to meet it. For the choice between lead and cement at the stack, Lead Flashing or a Cement Fillet? How to Tell Which You Have sets out the reasoning.

The order of work at the stack

A re-roof follows a sequence, and the stack is part of it. The old covering comes off, the underlay and battens are renewed and the new tiles are laid up to the point where the chimney interrupts the slope. At that stage the stack needs to be ready: pointed where required, with any loose brick or perished mortar dealt with so that the flashings have sound masonry to fix to.

The flashings then go in as the covering rises. The back gutter or saddle behind the stack is formed first, because it is under everything else. The soakers and stepped flashings follow up each side, interleaved with the tiles, and the apron goes in at the foot once the covering has reached it. Lead is chased into the mortar joints and secured, never simply stuck to the face.

This order is why timing matters. If the roofers finish the covering and leave the stack for later, the lead has to be fitted over completed tiles, which limits how well the soakers can be laid. If the stack has been repointed after the covering is on, mortar falls onto new tiles and stains them. Doing the stack at the right moment produces a better result than doing it separately, and often in less time. When you are weighing repair against rebuild, Repoint, Rebuild or Remove? How the Decision Gets Made will help.

Checking the stack while the roof is open

With the covering off, the stack can be seen as it has not been seen for a long time. The courses below the flashing line, normally hidden under tiles and lead, are exposed. Eroded joints, cracked bricks and leaning courses all show up. Dealing with them now needs no extra access, because the platform is already there, whereas finding them a year later means doing the whole thing again.

It also gives a chance to review the top of the stack. Flaunching, pots, cowls and bird guards can all be checked and, where needed, renewed at the same visit. A cap on a flue no longer used, or a guard on one that is, is a small addition when access is in place. Pointers on those are in Chimney Pots, Cowls and Bird Guards: Which Do You Actually Need?.

Anything inside the flue is a separate matter. Lining, sweeping, testing an appliance or deciding how a flue should terminate belongs to a HETAS or Gas Safe registered installer or a sweep, and we do not carry it out. We deal with the outside of the chimney: pointing, flaunching, leadwork, pots, cowls, guards, caps, rebuilds and rendering repairs.

Coordinating roofer and chimney specialist

The most common reason for a leak at a stack after re-roofing is a gap in responsibility. The roofing contractor assumes the chimney work belongs to someone else, or the chimney contractor was not told when the tiles would go on. Each does their own part correctly and the join between them fails.

To avoid this, agree in writing before the work starts who will form the stack flashings, who will point or repair the masonry and in which order. If one firm does both, the quotation should say so. If two firms are involved, the roofer should leave the stack zone clear and let the chimney specialist know the programme. A free written quotation from us can cover the stack on its own so it slots into the roofer’s schedule; see What Should Be on a Chimney Repair Quotation? for what it should contain.

On a roof with a dormer or a box gutter near the stack, the coordination matters even more, because those details interact. The wider picture of why bungalow roofs behave this way is on the chimney repairs in West Kirby page. If your stack is shared with a neighbour, Shared and Party Chimney Stacks: What You Can and Cannot Do Alone explains how that affects the arrangements, and a surveyor can advise on the specifics.

What to ask for when you receive quotations

Quotations for a re-roof often say little about the stack. Look for a line that names the chimney explicitly: the back gutter, the stepped flashings, the apron and who forms them. If the wording is only ‘make good around chimney’, ask what that means. A phrase that vague can cover anything from a proper lead dress to a bead of sealant.

It is also fair to ask what will happen if the stack turns out worse than expected once the tiles come off. A sensible contract says who decides, how you are told and how any change is recorded in writing before it goes ahead. That protects both sides and avoids an argument over a half-finished roof.

Finally, ask about weather. A roof left open overnight needs protection, and a stack that is half-flashed needs temporary cover. These are ordinary questions, and a contractor who has thought about them will answer without difficulty.

Not sure what you are looking at? Describe it and we will tell you what it is likely to be — 07464 259566, WhatsApp, or Evensbuddy@yahoo.com. If water is coming in now, please call rather than email.
FAQs

Common Questions

Can the old lead be reused on a new roof covering?
Rarely. Old lead has usually work-hardened and cracks when it is bent to a new profile. It is also unlikely to match the new levels. Fresh lead dressed to the new covering is simpler than the labour of removing and refitting the old, and produces a far better junction.
My roofer says the chimney is not part of his quote. What now?
Ask him to confirm exactly where his work stops, and in writing. The stack junction can be quoted separately, but someone has to be responsible for it and the programme has to allow for it. We provide free quotations for stack work and can coordinate with the roofer if you wish.
Should I repoint the stack before or after the new roof?
Ideally before the covering reaches the stack, or while the roof is open. Repointing afterwards risks mortar on new tiles and awkward access. If it must happen later, the area can be protected, but it is neater and often quicker to do it in sequence.
Is the underlay important around the chimney?
Yes. The underlay is turned up against the stack and sits beneath the flashings, so it forms the second line of defence if water gets past them. It should be cut and lapped carefully and not simply bunched. Mention it when you discuss the programme with your roofer.
More Advice

Other Chimney Guides

More from the West Kirby chimney series, then the wider guides.

Where We Work

Chimney Repairs Across Cheshire & the Wirral

Every town has its own page, written around the stacks that are actually on the roofs there. Start with the main chimney repairs page.

Customer Reviews

What Our Customers Say

5.0
★★★★★
74 Google reviews
★★★★★

“Excellent work replacing ridge tiles, repointing chimney and repairing flashing. Also fixed other broken tiles. Clean and tidy job. Would definitely recommend.”

Neil
★★★★★

“The guys did a great job in repairing our chimney. They were reliable, friendly and efficient. Buddy kept me in the loop throughout the whole process and I would not hesitate to use Roofline again!”

Hollie Furnival
★★★★★

“Highly recommend. Very quick and efficient. Great communication. Went above and beyond to work the weekend to complete the work that needed to be done. Very happy with the results.”

Karen Jones

Leave Roofline Solutions a Google review →

Free Quotation

Tell Us About the Chimney

Describe what you can see and roughly where you are, and we will come back to you — usually the same day. If water is coming in now, please call instead.

Prefer to talk? Call 07464 259566 · WhatsApp 0044 7464 259566 · Email Evensbuddy@yahoo.com

Find Us

Roofline Solutions, Elton, Chester

We cover Chester, Cheshire, the Wirral and Flintshire from Elton, just north of Chester.

Where We Are

2 Manley View
Elton
Chester
CH2 4QF

Almost all of our work happens at your property rather than here, so please call before travelling.

Opening Hours

Monday – Friday — 24hrs — Emergency Call-Outs
Saturday — 8:00 – 19:00
Sunday — 8:00 – 19:00

Weekday emergency call-outs are answered around the clock. Weekend cover is 8:00 to 19:00.