Chimney Advice · Northwich

Cracked Flaunching or a Cracked Stack? Telling Them Apart

Cracks at the top of a chimney may be a tired mortar cap or a sign that the whole stack is moving. Here is how to tell the two apart from the ground, and why the answer changes the repair.

★ 5.0 from 74 Google reviews
✓ Repointing, flaunching, leadwork & pots
✓ Fully insured
✓ Free written quotations
✓ Chester, Cheshire & Wirral
Home › Chimney Repairs › Chimney Repairs Northwich › Cracked Flaunching or a Cracked Stack? Telling Them Apart
The short version
  • Flaunching is the sloping mortar that holds the pots at the head
  • Head-only cracks usually radiate out from the pots
  • Cracks that run down the shaft point to the stack itself
  • Check whether a crack continues below the flaunching
  • Fix the stack first, then re-form the head

What the flaunching is for

The flaunching is the sloping band of mortar at the very top of the stack. It holds the pots in place and sheds rain outwards, away from the flues and the brickwork below. Because it is thin at the edges and exposed on every side, it is the part of a stack that suffers first, and cracks in it are very common.

That commonness is the problem. A cracked flaunching and a cracked stack can look alike from below, especially when the crack is at the top and the viewing angle is steep. They need quite different repairs, and mistaking one for the other either wastes money or leaves a structural problem untouched.

The aim here is to give you a way of telling them apart using only your eyes, perhaps a pair of binoculars, and a few photographs taken from the ground.

Pots in a row are usually bedded together, so a crack in one place may be the sign of a head that has shifted as a whole. It is worth looking at the stack as a unit before concentrating on any single crack.

Cracks that stay in the head

Flaunching cracks tend to be short and fan out from the base of each pot, rather like spokes from a hub. Others run along the edge where the flaunching meets the top course of brick, or across the top between two pots. They are usually fine at first, and open slowly as water gets in, freezes and lifts the surface.

The giveaway is that they stop. A crack in the flaunching ends at the brick course beneath it. It does not carry on into the shaft, and the brickwork below it looks tight and square. If you can see all this through binoculars, the crack is probably confined to the head.

Loose or leaning pots, bits of mortar on the roof or in the gutter, and moss growing in the cracks are all signs that the flaunching is past its best. These are repairs to the outside of the chimney, and the pots, cowls and guards are covered in Chimney Pots, Cowls and Bird Guards: Which Do You Actually Need?.

Another sign is the colour of the cracks. Pale, clean mortar dust below a pot suggests recent breakdown. Dark staining or green growth in the cracks suggests water has been getting in for a long time, which is useful to know when deciding how soon a repair is needed.

Cracks that run into the shaft

A crack in the stack proper is a different animal. It starts in the brickwork and often passes through the flaunching rather than beginning in it. It may be vertical, stepped or horizontal, as set out in our guide to Is It the Chimney? Working Out Where the Water Is Getting In, and it usually runs for several courses.

The evidence is continuity. A crack that carries on down below the head, or that appears on more than one face of the stack in a matching position, is not a flaunching problem. Neither is a gap opening between the flaunching and the top course, where the whole head has shifted. A visible lean in the pots against the ridge behind adds weight to the case.

Cracks that cross the line between head and shaft are the awkward middle ground. They may start as a flaunching fault and then run into the brick as water gets in, or the reverse. In that case the stack is treated first, because new flaunching bedded onto brickwork that is still moving will crack again.

Look too at the brick just beneath the flaunching. Bricks that have lost their faces, or joints that have washed out, are often the result of years of water running off a failed head. Fixing the head early protects the brickwork below, which costs far more effort to put right once it has gone.

A simple ground check

From a spot where you can see the top of the stack square on, note the pots against the ridge or a neighbour. Are they upright and evenly spaced? Then look at the top course of brick: is it level, or does it step? Finally, trace any crack downward with binoculars and ask whether it stops at the flaunching or keeps going.

Photographs help. Take one from the same position now and another a month later, and compare. A flaunching crack that has not changed is likely to be a surface fault. One that has grown, or has a gap on one side of it, suggests movement.

Please do not climb or lean from a ladder to look closer. At the top of a roof, with a heavy stack above you, it is a poor place for a close inspection.

A sharp phone zoomed in on the stack works nearly as well as binoculars, and the picture can be sent to us on WhatsApp. We can usually say whether the problem looks like a head repair or something more, though a definite answer needs a proper look at the stack.

What happens next in each case

If the fault is confined to the flaunching, the usual work is to cut out the cracked mortar, lift the pots, and re-form the flaunching with a fresh bed sloping away from each pot. It is a contained job on the outside of the chimney, and we can give a free written quotation. Our page on Repointing a Chimney: Why the Mortar Mix Matters More Than the Finish describes the mortar choice.

If the stack itself is cracked, the head cannot be finished until the brickwork is dealt with, by repointing, a part rebuild or a full rebuild. Where the pattern suggests wider movement, the page for chimney repairs in Northwich explains why we may suggest a structural engineer first. Flues and appliances stay with a HETAS or Gas Safe registered installer or a sweep.

It is worth knowing that a head repair and a pot replacement often go together, because lifting the pots to re-form the flaunching is the moment to check them for cracks and frost damage. The same visit can fit new cowls or guards if the stack needs them.

Not sure what you are looking at? Describe it and we will tell you what it is likely to be — 07464 259566, WhatsApp, or Evensbuddy@yahoo.com. If water is coming in now, please call rather than email.
FAQs

Common Questions

Can cracked flaunching just be painted over?
Paint and coatings only cover the surface and do not stop water entering the crack or hold the pots in their bed. The cracked mortar needs to be cut out and re-formed. Anything else buys little time, and trapped moisture can speed up damage to the mortar underneath.
How long does flaunching last before it cracks?
There is no fixed life, because it depends on the mix, how well the pots were bedded and how exposed the stack is. Some stay sound for a long time and others crack within a few winters. The condition matters more than the age, so check it rather than count years.
Do loose pots always mean the flaunching has failed?
Nearly always, because the flaunching is what holds them. Pots can also be loose if the top course beneath has cracked or shifted. If a pot moves or leans, keep clear of the area below and have the head looked at soon, since a falling pot is heavy.
Is it worth re-forming just the flaunching to save money?
If the crack is genuinely confined to the head, yes, it is the right repair. If the stack below is cracked or moving, new flaunching will not last, so it is better to treat the cause first. A proper look will establish which situation applies.
More Advice

Other Chimney Guides

More from the Northwich chimney series, then the wider guides.

Where We Work

Chimney Repairs Across Cheshire & the Wirral

Every town has its own page, written around the stacks that are actually on the roofs there. Start with the main chimney repairs page.

Customer Reviews

What Our Customers Say

5.0
★★★★★
74 Google reviews
★★★★★

“Excellent work replacing ridge tiles, repointing chimney and repairing flashing. Also fixed other broken tiles. Clean and tidy job. Would definitely recommend.”

Neil
★★★★★

“The guys did a great job in repairing our chimney. They were reliable, friendly and efficient. Buddy kept me in the loop throughout the whole process and I would not hesitate to use Roofline again!”

Hollie Furnival
★★★★★

“Highly recommend. Very quick and efficient. Great communication. Went above and beyond to work the weekend to complete the work that needed to be done. Very happy with the results.”

Karen Jones

Leave Roofline Solutions a Google review →

Free Quotation

Tell Us About the Chimney

Describe what you can see and roughly where you are, and we will come back to you — usually the same day. If water is coming in now, please call instead.

Prefer to talk? Call 07464 259566 · WhatsApp 0044 7464 259566 · Email Evensbuddy@yahoo.com

Find Us

Roofline Solutions, Elton, Chester

We cover Chester, Cheshire, the Wirral and Flintshire from Elton, just north of Chester.

Where We Are

2 Manley View
Elton
Chester
CH2 4QF

Almost all of our work happens at your property rather than here, so please call before travelling.

Opening Hours

Monday – Friday — 24hrs — Emergency Call-Outs
Saturday — 8:00 – 19:00
Sunday — 8:00 – 19:00

Weekday emergency call-outs are answered around the clock. Weekend cover is 8:00 to 19:00.