“Excellent work replacing ridge tiles, repointing chimney and repairing flashing. Also fixed other broken tiles. Clean and tidy job. Would definitely recommend.”
NeilRepairs on a period stack are judged by how well the new work reads as the old: the pattern the bricks are laid in, and the shape the mortar is finished to. Here is how both are identified and matched.
Bond is the arrangement of bricks in a wall, and every old brick wall follows one. In English bond, courses of long faces (stretchers) alternate with courses of short ends (headers). Flemish bond puts stretchers and headers alternately in every course. Stretcher bond, which is all long faces, appears where the wall is only half a brick thick, and various garden-wall and stack patterns mix these ideas. The pattern is part of why an old stack looks the way it does.
A stack is small, so the bond is quick to read if you take time over it. Stand back, look at one face with binoculars from the garden, and follow a single course along. Do headers appear, and how often? Are there bands of bricks laid on edge or at an angle? Do the corners have a particular arrangement, with a quoin at the angle of each course? Photographing each face square-on, rather than from a steep angle, makes the pattern easier to study afterwards.
Be wary of earlier repairs. Over the life of a stack, sections are often rebuilt by someone who laid the new bricks in the easiest pattern rather than in the original one. That produces a patch where headers vanish or the course lines drift, and the patch is where the repair to be avoided is most obvious. Copying the original bond, and not the nearest repair, is the aim.
The profile is the shape the mortar is given at the surface once it has been laid. A flush joint is trowelled level with the brick. A struck joint is angled, sloping in at the top or at the bottom. A weathered joint slopes so its top is recessed and its lower edge sits forward, which sheds water outwards. A tuck-pointed joint has a thin raised line set over a flat ground, intended to make the bricks look more regular than they are. A recessed or raked joint is cut back from the face.
These shapes matter for two reasons. Visually, they change the shadow lines on the wall and so the colour you perceive at a distance; a deeply struck joint looks darker, a flush one lighter. Functionally, a profile that holds water, such as a deep recess on an exposed stack, lets rain sit against the brick and the mortar, and in frost that is how damage begins. For the mortar itself, Repointing a Chimney: Why the Mortar Mix Matters More Than the Finish explains what the mix should be on soft old brick.
The old profile is often hard to see because the mortar has weathered. Look in the sheltered parts of the stack, under an oversailing course or behind the pots, where the original finish may survive. A raking-out that goes deeper than needed destroys the evidence, so the shape is recorded before anything is removed.
It is natural to assume a stack was built in one pattern all round, but that is not always the case. Visible faces facing the street were sometimes laid with better bricks and finer joints than the back, and a side that backs on to a neighbouring roof may be plainer still. A stack that serves two houses may have been built at two different times.
This means each face is read separately. Joint width can vary too: a fine joint on the front and a wider one on the rear are normal on some buildings and need to be copied that way, not averaged out. The same goes for the head, where a decorative band, an oversail or a dentil course may be finished differently from the shaft.
If the brickwork has been repointed in the past, read through it. Look for the width of the original joints on the brick faces, usually visible as the line where old mortar meets the arris. A fine original joint will have been widened if it was raked out too aggressively, and restoring a narrower line may not be possible, in which case the aim becomes making the new work sit calmly beside it.
The best way to agree a finish is to make a small sample. A panel of a few bricks, pointed in the proposed mix and profile, shows colour, texture and shadow in a way that no description does. It should be judged dry, because lime mortar changes colour as it cures, and viewed from the ground in daylight, since that is how the stack is seen. Looking at it from two metres does not tell you how it will read from the street.
The same panel is useful if the council is involved. A photograph of the sample next to a photograph of the existing wall gives an officer something concrete to comment on, and a note of the mix and the sand makes it repeatable. Where several operatives work on the job, it also keeps the standard consistent across the faces.
Sample panels are not a delay in practice; they are a short step at the start that avoids a conversation at the end. It is much easier to change a trial patch than a finished stack. What Should Be on a Chimney Repair Quotation? describes how a written quotation can say what is being matched and how.
No repair is invisible. New mortar looks different for a season or two, new brick is rarely identical to old, and a stack that has weathered for generations has a patina that cannot be reproduced. The aim is for the repair to read as part of the stack from the ground, and for the character of the bond and joint to be unchanged.
On a protected building the council has the last word on whether a match is acceptable, and we would encourage you to put the question to the conservation officer before work starts. That applies particularly in a town like Knutsford, where chimney repairs in Knutsford describes how much of the roofscape is protected. This is general information, not legal advice.
Flue linings and appliance testing remain a matter for a HETAS or Gas Safe registered installer or a sweep. Our work is on the outside of the stack, and we are fully insured and give free written quotations.
More from the Knutsford chimney series, then the wider guides.
Every town has its own page, written around the stacks that are actually on the roofs there. Start with the main chimney repairs page.
“Excellent work replacing ridge tiles, repointing chimney and repairing flashing. Also fixed other broken tiles. Clean and tidy job. Would definitely recommend.”
Neil“The guys did a great job in repairing our chimney. They were reliable, friendly and efficient. Buddy kept me in the loop throughout the whole process and I would not hesitate to use Roofline again!”
Hollie Furnival“Highly recommend. Very quick and efficient. Great communication. Went above and beyond to work the weekend to complete the work that needed to be done. Very happy with the results.”
Karen JonesDescribe what you can see and roughly where you are, and we will come back to you — usually the same day. If water is coming in now, please call instead.
Prefer to talk? Call 07464 259566 · WhatsApp 0044 7464 259566 · Email Evensbuddy@yahoo.com
We cover Chester, Cheshire, the Wirral and Flintshire from Elton, just north of Chester.
2 Manley View
Elton
Chester
CH2 4QF
Almost all of our work happens at your property rather than here, so please call before travelling.
Monday – Friday — 24hrs — Emergency Call-Outs
Saturday — 8:00 – 19:00
Sunday — 8:00 – 19:00
Weekday emergency call-outs are answered around the clock. Weekend cover is 8:00 to 19:00.