Chimney Advice · Crewe

Lead at the Stack Against Slate and Against Tile

Lead flashings are not one-size-fits-all. Slate and tile need different details where they meet a stack, and a mismatch is a common reason for a leak.

★ 5.0 from 74 Google reviews
✓ Repointing, flaunching, leadwork & pots
✓ Fully insured
✓ Free written quotations
✓ Chester, Cheshire & Wirral
Home › Chimney Repairs › Chimney Repairs Crewe › Lead at the Stack Against Slate and Against Tile
The short version
  • Slate is flashed with individual soakers and a stepped cover flashing.
  • Tiles are flashed to suit their profile, and deep profiles need extra care.
  • A detail copied from the wrong roof covering leaves gaps you cannot see.
  • Soakers are hidden once the roof is finished, so ask what is being fitted.
  • Check the stack from the ground only.

Why the Roof Covering Dictates the Lead

Where a roof meets a chimney, the job is to stop rain getting between the two. The brickwork is vertical and rigid, the roof covering is sloping and made of many small overlapping pieces, and the flashing has to bridge the two without leaving a path for water. How it does so depends entirely on what the roof is covered in, because slate and tile are laid and overlap in different ways.

Slates lie flat and thin and overlap in even courses. Plain clay tiles also overlap in courses, but are thicker and curved slightly. Profiled tiles, the interlocking type with ridges and troughs, do not lie flat at all and must be dressed over rather than tucked under. A roofer who knows the covering will choose the detail to suit it. A flashing that is correct on one roof can be wrong on another, and the error rarely shows on the day the work is finished. It shows the first time a long spell of rain arrives from the wrong direction.

This is why a quotation for stack leadwork should name the covering. It is also why the advice in Lead Flashing or a Cement Fillet? How to Tell Which You Have is only the first step. Choosing lead over a mortar fillet is right, and then the question becomes how that lead is formed and fixed on the roof in front of you.

Soakers and Stepped Flashings on Slate

On a slate roof, the traditional detail against a stack is a soaker at every course. A soaker is a small rectangle of lead, bent to an angle, with one leg lying flat under the slate and the other turned up against the brickwork. Each slate course gets its own soaker, so water running down the face of the stack is led onto the slate below and cannot get under it. Over the turned-up edges goes a stepped cover flashing, let into the brick joints and dressed down over the soakers.

Because the soakers sit under the slates, you cannot see them once the roof is finished. That is a strength of the detail, because it is neat and long-lasting, and a weakness for anyone checking the work. Slate roofs, like the terrace roofs described on the chimney repairs in Crewe page, are brittle and best not walked on, so the soakers are often renewed only when the slates beside the stack are lifted and relaid.

What goes wrong is easy to describe. Soakers get left out when a repair is done in a hurry and the cover flashing is simply tucked behind a slate. Or a continuous strip of lead is laid in place of individual soakers and, being flat, it channels water sideways. The first sign is often a dark stain on the ceiling and a slightly damp patch beside the breast, long before anything looks wrong outside.

Lead Against Tile: Profile Matters

Plain tiles are the nearer relation to slate, and they can be flashed in much the same way, with soakers working with the tile courses and a stepped flashing above. Tile is thicker, so the lead has to be shaped to sit cleanly and avoid kinks, and the flashing is usually larger to cover the greater depth. Where the tiles are heavier, the roof structure beside the stack needs to be sound and the tile battens straight, or the lead cannot lie flat.

Profiled tiles are different. Their ridges and troughs leave gaps against a vertical face, and a flat strip of lead does not fill them. Either the lead is dressed to follow the profile, using a malleable lead with a good upstand, or a purpose-made flashing system is used, or the tiles beside the stack are cut and the gaps managed with an undercloak and a flexible dressing. Whichever is chosen, it is a detail worked out for that tile, not a standard apron laid on top. The cut tiles beside the stack matter as well: they should be trimmed neatly and fixed, not left as ragged pieces with the gap packed with mortar, because that packing is the first thing to fall out.

There is a limit to how far lead can be bent without harm. Very deep profiles make lead work hard, and over-forcing it thins and cracks it at the folds. A roofer will often prefer a larger area of lead with a gentle dressing to a tight one. If you want a view on the kinds of work this involves, the main page on Repoint, Rebuild or Remove? How the Decision Gets Made covers the broader decisions.

What a Mismatch Looks Like

The commonest mismatch is a slate-style detail on a tile roof or the reverse. On tile, a short, flat apron nailed over the profile leaves gaps at the troughs, and wind-blown rain finds them. On slate, an apron with no soakers beneath it relies on a single line of sealant, and sealant dries out and splits.

From the ground you can look for signs without going near the roof. Binoculars will show lead that has lifted or is hanging away from the brick, a bead of mastic along the top edge, or a grey mortar line where lead should be. Streaks of white or dark staining running down the stack below the junction suggest water is arriving there. Inside, a stain that grows after heavy rain and fades when it is dry points the same way.

The remedy is not to dab more sealant on. It is to strip the flashing back and renew the lead in the form that suits the covering. Sometimes that means lifting a few slates or tiles beside the stack, and a good roofer will say so in advance. Any covering that is broken in the process should be replaced and the roof left as watertight as it was found. It is also worth asking whether the neighbouring junctions, such as the ridge either side of the stack, are being checked at the same time. We give free written quotations and describe exactly what is being renewed and why.

Not sure what you are looking at? Describe it and we will tell you what it is likely to be — 07464 259566, WhatsApp, or Evensbuddy@yahoo.com. If water is coming in now, please call rather than email.
FAQs

Common Questions

Can lead be reused when the stack is repaired?
Usually not. Old lead work-hardens, may be thinned or cracked at the folds, and rarely refits once pulled back from the brick. It is normally renewed, with the new flashing formed to the roof covering you actually have. If the old lead is in good condition and is not being disturbed, it may be left.
Why can I not see the soakers on my slate roof?
They sit under the slates by design. Only the turned-up edge against the stack and the stepped cover flashing above are visible. If you want to know whether soakers are fitted, you need either a roofer who has lifted the slates or an honest statement in the quotation about what is being done.
Is a chimney tray the same as a flashing?
No. A flashing keeps rain out of the junction between roof and stack. A tray is a damp-proof layer built into the brickwork inside the stack. They do different jobs, and a stack can have one without the other. A roofer can tell you what is there once the work is open.
Does the roof covering change how the scaffold is set up?
It can. Brittle slate and old tile should not be walked on, so the work is done from a platform at the stack. That affects how the scaffold is built and tied. It is something we plan before the work starts, rather than leaving it to be sorted out on the day.
More Advice

Other Chimney Guides

More from the Crewe chimney series, then the wider guides.

Where We Work

Chimney Repairs Across Cheshire & the Wirral

Every town has its own page, written around the stacks that are actually on the roofs there. Start with the main chimney repairs page.

Customer Reviews

What Our Customers Say

5.0
★★★★★
74 Google reviews
★★★★★

“Excellent work replacing ridge tiles, repointing chimney and repairing flashing. Also fixed other broken tiles. Clean and tidy job. Would definitely recommend.”

Neil
★★★★★

“The guys did a great job in repairing our chimney. They were reliable, friendly and efficient. Buddy kept me in the loop throughout the whole process and I would not hesitate to use Roofline again!”

Hollie Furnival
★★★★★

“Highly recommend. Very quick and efficient. Great communication. Went above and beyond to work the weekend to complete the work that needed to be done. Very happy with the results.”

Karen Jones

Leave Roofline Solutions a Google review →

Free Quotation

Tell Us About the Chimney

Describe what you can see and roughly where you are, and we will come back to you — usually the same day. If water is coming in now, please call instead.

Prefer to talk? Call 07464 259566 · WhatsApp 0044 7464 259566 · Email Evensbuddy@yahoo.com

Find Us

Roofline Solutions, Elton, Chester

We cover Chester, Cheshire, the Wirral and Flintshire from Elton, just north of Chester.

Where We Are

2 Manley View
Elton
Chester
CH2 4QF

Almost all of our work happens at your property rather than here, so please call before travelling.

Opening Hours

Monday – Friday — 24hrs — Emergency Call-Outs
Saturday — 8:00 – 19:00
Sunday — 8:00 – 19:00

Weekday emergency call-outs are answered around the clock. Weekend cover is 8:00 to 19:00.